Properly control boost with this solenoid connected to your ECU.
The CIM module is normally installed in the vehicle. This places the electronics in the vehicle rather than in the cable which has the advantage of providing the correct signals to connect directly to a dash or data logger as well as providing a connection point for a PC. The CIM module ..
This version is intended for fuel flow sensors which have a very low trigger level. Heavy filtering minimises the possibility of interference, resulting in significant variation of the trigger level with frequency.
The Dual Magnetic Converter (DMC) converts magnetic style signals to open collector ..
This version is intended for engine trigger sensors that have insufficient amplitude to trigger a logic level input. Minimal filtering avoids delays in the signal. The trigger level does not vary significantly at normal operating frequencies.
The Dual Magnetic Converter (DMC) converts magnetic styl..
This version is intended for ignition system input conditioners, typically used in drag racing, for measuring ignition timing.
The Dual Magnetic Converter (DMC) converts magnetic style signals to open collector output signals a square wave. This makes a typical magnetic sensor behave as a switche..
This version is intended for magnetic wheel speed sensors. The signal should be symmetrical around zero volts. Heavy filtering minimises the possibility of interference, resulting in significant variation of the trigger level with frequency.
The Dual Magnetic Converter (DMC) converts magnetic style..
The Dual Half Bridge (DHB) is a high current amplifier which allows low current auxiliary outputs to drive high current loads such as motors. It contains two high current half bridge outputs enabling it to drive a single motor in two directions, or drive two motors in a single direction. It is also ..
Need a tested and proven solution for your new USB Logger but don't want or need the higher end units we offer? This is right up your alley then.
Sandisk 32GB 3.0 Flash Drive has read rates of 130MB/sec. It also includes a small hole so you can install a lanyard to easily keep track of it. Come..
THIS KIT IS DESIGNED TO WORK WITH DRIVE BY WIRE THROTTLE BODIES FOR PROPER THROTTLE BLIPPING.
The GPS-L10 is a 10 Hz GPS which combines the electronics and antenna into one small unit. A highly sensitive receiver allows the GPS to lock onto signals even in difficult environments. It is fitted with a DTM connector and is pre-configured to be compatible with MoTeC Dash/Data Loggers. It is..
The GPS-L5 is a 5 Hz GPS which combines the electronics and antenna into one small unit. A highly sensitive receiver allows the GPS to lock onto signals even in difficult environments. It is fitted with a DTM connector and is pre-configured to be compatible with MoTeC 'Hundred Series' a..
32 GB USB DATA PLUG
Internal USB3 memory stick
Resistant to water, vibration, the elements
This cable only fits the standard USB cable offered here: https://milspecwiring.com/store/index.php?route=product/product&product_id=2213
The Beacon Receiver (BR2) is the part of the lap timing system that is fitted in the vehicle. Depending on the other components in the application, the receiver can be connected using a switched output or a CAN bus and should be set up accordingly.
Fitting the BR2
The BR2 should be fitte..
The Beacon Transmitter (BTX) is the track side mounted part of the lap timing system.
Mounting the BTX
The narrow infrared beam emitted by the BTX should be aimed parallel to the road and at the same height above the road as the receiver in the vehicle. The transmitter mounting system should there..
USB to CAN adapter (includes USB cable)
Software Requirements for UTC Compatibility
M400, M600, M800, M880 - V2.30S or later
PDM16, PDM32, PDM15, PDM30 - V1.0 or later
BR2 - V188.8.131.52 (this software ships with all data logging manager software)
DBW4 - V1.03 or later
Connecting to the PC's Serial Port
Use either a PC Interface cable (PCI cable) or a Computer Interface Module (CIM).
The PCI cable contains electronics in the ECU end of the cable to convert the ECU signals to signals compatible with the serial port on the PC
32 GB AUTOSPORT USB DATA PLUG
Professional level, military spec - built for maximum data integrity
Internal USB 3.0 memory stick
Mechanically latched with a keyway that easily locates into the mating connector – ideal for fast changeovers in locations that are difficult to se..
The STC (Serial to CAN) adaptor converts RS232 data to CAN and vice versa allowing multiple RS232 devices to be connected to a Data Logger via CAN.
The VSM Video Sync Module allows automatic synchronisation of in-car footage to the logged data for video analysis in MoTeC i2 Pro data analysis software.
The module connects between the microphone and video recorder of the in-car camera and to an auxiliary output of the Da..